How to use CGDI FC200 ECU Programmer to clone Audi Gearbox DL382 data? Audi gearbox clone only supports to do on bench, NOT support OBD method, please disassemble gearbox module before operation. The clone procedure will need to read & write D Flash, EXT D Flash, P Flash. Read the steps below to learn how to do. Identify Start CG FC200 software, Select car brand “Audi”. If you don’t know its model, enter “DL382” in search box. It’ll display a model in ECU: VAG_TEMIC_DL382 TC1784, just select it. On bench >> Wiring diagram Follow the diagram to connect Audi gearbox. Click “identify”. CPU info has successfully read out, which means connection is OK. Read & Write Data Click “Read D Flash”, then save file. Click “Read EXT D Flash”, then save file. Click “Read P Flash”, then save file. P Flash reading will take for minutes, please wait and do not remove the module. After reading completed, write data separately in turn. Click “Write D Flash” to load saved file. Click “Write EXT D Flash” to load saved file. Click “Write P Flash” to load saved file. That’s all, very easy to do. Note: Please click “Disconnect” before removing gearbox module. It may help:
CGDI FC200 Clone BMW Gearbox F Series 6HP Data http://blog.obd2shop.co.uk/cgdi-fc200-clone-bmw-gearbox-f-series-6hp-data/ CG FC200 supports 4200 types of ECU, covering 80% models on market. If you’re not sure about its coverage, feel free to contact us. www.obd2shop.co.uk
0 Comments
The answer is yes. Yanhua Mini ACDP + Module 13 support to clone Volkswagen gearbox. Besides, Mini ACDP can also support Audi DQ200(0AM/0CW), DQ250(02E/0D9), DL382(0CK), DL501(0B5), VL381(0AW) models and etc. ACDP module 13 interface board replaces the traditional wiring connection to make it easier. It’s much efficient & safe, can greatly save time when programming. The connection diagram can be found in Help. 1. Make sure the model & SN of gear box. 2. Install interface board into gearbox as image. 3. Connect ACDP, OBP+ICP adapter, interface board & gearbox. Now you can start to clone VW gearbox!
www.obd2shop.co.uk Problem After installing KESS V2 software, no matter which car model or ECU selected, there are no connection diagrams. It only gives me a blank page. What’s the reason? Solution
The reason why causes this issue is because of TF card. 1. Take out TF card from KESS to clean, then reinsert to have a try; 2. If issue still persists, which means the TF card is damaged. Please exchange a new TF card. This is how to solve KESS software is unable to display connection diagram problem. Hope it is helpful. www.obd2shop.co.uk Problem Each time when I was opening SVCI 2020 software to start DAS manager, it always came out a warning: “This option is not available in the current version. License missing”. Any ideas? Please help. Solution
The reason why this warning coming out is because of the incorrect SVCI version. Please download SVCI 2020 V12.0 version, then update firmware. Free download SVCI 2020 V12.0 https://mega.nz/file/Z8hGjQDK#bRwvtu0kROC0l2YP051lN_Lbqozu34tEYt8DiRu6nQs This may help: How to update SVCI 2020 Abrite Commander firmware? http://blog.obd2shop.co.uk/how-to-update-svci-2020-abrite-commander-firmware/ Update Thanks to Obd2shop engineer, problem was solved. www.obd2shop.co.uk
This is the 2022 latest operation guide on Thinkcar Pro Mini OBD2 Scanner installation, registration, activation & software download for beginners. Follow the steps below to learn how to get start.
Video guide:
How to install Thinkcar Pro app?
For Android system, search & install “Thinkdiag” in Google Play. For IOS system, search & install “Thinkdiag” in App Store.
How to register Thinkcar Pro account?
Open Thinkdiag app, Login >> Sign up >> Enter user name & password, next >> Next >> Enter Email to get verification code Registered successfully.
How to activate Thinkcar Pro device?
User >> My devices >> Activate >> Enter serial number & activation code, activate * SN is in the device. * Activation code is in the manual Congratulations. The device has been activated successfully!
How to download Thinkcar Pro software?
Installed already >> Download/No You can either automatically download or manually select appropriate maintenance & vehicle diagnostic software to download. Autel MaxiIM IM608 Pro can program 2017-2020 Chevrolet Silverado all key lost via OBD successfully. Besides, it also supports to do add key & read password. Autel IM608/ IM508 + XP400Pro has same immo function but cost-efficient than IM608Pro, which is a good investment for locksmiths. More vehicle coverage please check: https://www.autel.com/vehicle-coverage/coverage2 Following is using Autel IM608 Pro as an example. FCC: HYQ1EA Note: Must have 2 smart keys. Connect Autel IM608 with OBD, press IMMO >> Accept >> Chevrolet >> Manual selection >> USA >> Silverado 3500 >> 2017-2020 >> Smart key >> Yes >> Immo status scan Press START/ STOP button once. Clear DTC(If any) >> All smart keys lost >> Start Do you want to start PIN data reading? Yes (If PIN data of current vehicle has been read and saved, press “No”.) Make sure IM608 has network connected with successfully. Note: 1.For this function process, it is recommended to use a USB cable connect the diagnostic tool to VCI, otherwise the function may fail. 2.For some models, network connection is required for execution of this function. Ensure stable network connection. PIN code read successfully, please record. Do you want to start DTC clearing? Yes Do you want to start key learning? Yes Press START/STOP button once. Place the smart key to be learned into the key slot and take other keys out of the vehicle. The key slot is usually: 1.In the armrest box. 2.Under the bottle rack. 3.Besides the ash tray. 4.In the glove box. IM608 will fill in the pin code automatically. Switch ignition off. Wait processing until 100%... Press the START/STOP button once. The current key is complete the matching. Press “Yes” to program next key, otherwise “No”. Switch the ignition off. Press the START/STOP button and hold for 12s. Release the START/STOP button. Long press the START/STOP button to turn the ignition on until the instrument light illuminates.(If the instrument light is not illuminating, please release the START/STOP button and repeat it.) Switch the ignition off.
Depress the brake, press START/STOP button to start the engine and wait 5s. Switch ignition off. Note: 1.Turn off the engine. 2.Open and close the driver door. 3.Remove the smart key, press the lock and unlock buttons simultaneously, and then release the buttons. Is there another key to be synchronized? No Number of matched key: 1 Test the key, it does work well. Programming has done! This is how to use Autel IM608Pro to program Chevy Silverado 2017-2020 all keys lost successfully. This is a tutorial on how to use VXDIAG VCX SE engineer edition software to do BMW E series programming & coding. Step1. Open ITool Radar software, Reserve >> Duplicate device IP; Step2. Open EasyConnect software to paste device IP, selected “ICOM Lock” then “Check”; Step3. Open Winkfp software, click Comfort mode >> Choose ZUSB >> Choose assembly identification number/ integration position(ECU family, ZB-number & Integration position) >> OK >> Done >> Enter VIN >> Program The user info field can still be programmed 1 times. Program ECU? Click “OK”. Programming OK. Step4. Open NCS Expert software, click File >> Load profile >> Default profile >> VIN/ZCS/FA >> ZCS/FA I ECU >> Choose chassis: E70 >> Choose ECU: CAS >> Back >> Program ECU >> Choose ECU: JBBF >> Execute job
Coding active. How to do in case Lonsdor K518ISE is stuck due to misoperation and cannot force to update? At this time, users may need to flash K518 key programmer to reboot device. If you’re struggling with same problem, feel free to contact Obd2shop online service for the flash package. How to flash K518 programmer? 1. Download & unzip flash package; 2. Install & open “PhoenixSuit_CN” app; 3. Connect K518ISE with a USB cable; 4. Flash K518ISE: One-click flash >> Load >> Locate “sun8iw5p1_android_dvk3” file; 5. Hold on power button to enter below interface. Click “Reboot” then immediately hold on the Volume+ button until coming out a prompt message on computer. Continuous click “Yes >> Yes” to start update firmware; 6. Pull out USB cable when update completed. Wait K518ISE device to repair automatically; 7. Don’t touch K518 Programmer until showing a white screen with “Set up WIFI”&“Update” buttons;
8. Set up WIFI then update, the problem will be solved after updating. It may help: How to do formatting for Lonsdor K518ISE key programmer? http://blog.obd2shop.co.uk/how-to-do-formatting-for-lonsdor-k518ise-key-programmer/ Xtool M821 Adapter is newly coming soon. Designed to program Mercedes Benz all key lost. Should work with XTOOL X100 PAD3 or X100 Max &KC501 Key Programmer together. To improve 65% efficiency, no need to plug or unplug hundreds of times. Note: Please first update your Mercedes Benz key programming software to the latest version 27.10. Xtool M821 Mercedes-Benz Car List Supported: What is in the Xtool M821 package? M821 Mercedes Benz AKL adapter J1K02_BENZ_Wiring Harness Quick Guide How to connect M821 Communication Adapter?
1. Connect Xtool device & KC501 via USB; 2. Connect Mercedes Benz IR emulator with KC501; 3. Disconnect OBD2 connector from main cable, connect Xtool device(or VCI box) with M821 Adapter by main cable; 4. Use 12V power supply to main cable; 5. Connect EIS/EZS module with M821 Adapter by J1K02_BENZ_cable. Note: *Please check wiring diagram in Xtool device when connecting M821 Adapter & EIS/EZS module via J1K02_BENZ_cable. *The Mercedes Benz IR emulator should insert into the slot of the module when operating. *For device with a VCI box, connect 821 Adapter with VCI box by main cable, keep VCI box connected with the device via Bluetooth. More details can check in device when connection. More questions welcome to contact us. www.obd2shop.co.uk How to program a new smart key for Toyota Corolla 2016 via OBD? The procedure includes unlock smart key with Xhorse VVDI Mini Key Tool, register new key with Autel MaxiIM IM608/ IM508 Key Programmer. Unlock Smart Key Put the key into VVDI Mini Key Tool slot, press Special Function >> Unlock Toyota Smartkey >> Unlock Unlock OK. Read key info, it is a Toyota 8A smart key. Add New Smart Key
In this step, you’ll also need a working key. Plug Autel IM508 or IM608 connector into OBD. After the car model was identified, go to Special function >> Smart code registration >> OK This function is for registering a key. Turn the ignition/ power switch on(engine off/ read off). Do not carry any device which may generate electric waves into the vehicle, such as a cellular phone. Note that each step must be performed within a specific amount of time. Do not carry 2 or more keys into the vehicle. This may cause the function to fail. Number of available spaces for new codes: 6 Number of registered key codes: 1 Check the current number of key codes, press “Next”. Ensure that the 2 types of keys are separated and placed 30cm(1ft) or more from the vehicle. 1. Separate the 2 types of keys; 2. Place a registered key into the vehicle. Touch the ignition with a registered key(beep) in 30s. Number of key to confirm: 1 Press “Start”. Touch the ignition with a new key to be registered in 30s. 1. Remove the registered key from vehicle. 2. Place a new key into the vehicle. 3. Touch the ignition with new key to be registered.(beep) Key code registration is completed. Let’s check the new key, it can use normally. Done! |
Archives
April 2024
Categories
All
|