Autel MaxiIM IM608 + XP400 Programmer can program a new key for Volkswagen Passat 2012 successfully. It allows to do add key, all keys lost, read password, remote learning for Passat vehicles as below:
Autel IM608 IMMO VW(EU)Car List:
Autel IM608 IMMO VW(US) Car List
Tools
Autel MaxiIM IM608 scan tool Autel XP400 key programmer An original key A new key Steps Connect Autel IM608 with OBD, turn ignition on, press IMMO >> Accept >> Volkswagen >> Smart selection >> Yes >> OK >> It’s 2 keys on the vehicle, press “Esc”>> Key add >> Yes
Wait reading IMMO data processing until 100%...
Do you need to make dealer key? Yes Put a blank key in XP400 programmer keyhole, press “OK”. Key locked, attempt to unlock it? Yes Make dealer key success! Press “OK”.
Continue to generate the next key? No
Place the dealer key in XP400 programmer, press “OK”. (It’s the new key we just made) The following operation will modify the instrument data. The ongoing process is non-interruptible, or it may cause damage to the instrument. Press “OK” Add key success! Press OK >> OK It shows 3 keys on the vehicle now. Let’s test the new key, here we go, everything is perfect, it can start the engine.
Done!
That’s another key added. For remote function, you can go to “Remote control add” or “Remote control learning” to do it. I’ve already done. Using Autel IM608 & XP400 Key Programmer to add key for a VW Passat 2012 is quite easy and fast. https://www.obd2shop.co.uk/
0 Comments
Sometimes, Lonsdor K518ISE Key Programmer may meet some problems to crash, or stop working. You’ll need to format the device. How to format Lonsdor K518ISE? Step1. Hold 2 buttons marked in red meanwhile, you’ll go into the interface as below. Step2. Press “Arrow Button”>>“Factory Setting”. The device will show a prompt warning: “This operation will clear apk related data and reinstall, please operate carefully!!!”. Press “OK”. Step3. Press “Repair”>>“Oldest APK”, wait APK installing until completed, press “Return”. Step4. Press “Start APK”, and connect device with WIFI. Press “Update”>>“OK” to update. Thus, you can use K518ISE programmer normally again after updating.
This is the procedure of formatting Lonsdor K518ISE step by step. https://www.obd2shop.co.uk/ Xtool X100 Pad3 (X100 Pad Elite) can program a new key for Chrysler Dodge Charger successfully. How to program? Plug X100 Pad3 connector into OBD2 port, press Diagnosis >> Dodge >> Agree >> Proximity/Fobik(RFH) >> Charger 11- >> Read security code >> OK Go back to press Erase smart keys >> Input security code >> OK Erase success. Go to “Add smart key”. Emergency light open and turn ignition off, press “OK”. Put the key near to center console, then press UNLOCK once in 30s. Press “OK”. Program completed. Press “OK” to finish. Let’s test the key in the end, it does work well. Done! Using Xtool X100 Pad3 to program a key for Dodge Charger is quite fast and easy, it takes me only 3 minutes to be done.
Today I’m gonna use Obdstar X300M to do mileage adjustment for a 2008 Mazda 6 four-cylinder. As you can see, the odometer is 131986km now. Plug the connector with OBD2 port, press Cluster calibrate >> Mazda >> Mazda V30.73 >> Manual selection >> M6 >> 2005-2009 Switch ignition on, press “ENT”. Before modify mileage, please execute “Data backup” function. Press “ENT”. Turn off the ignition switch and then turn the ignition switch... Press “Data backup”. Turn off the ignition switch and then turn the ignition switch... Backup data... Input value to rename & save file. Operation success. Mileage adjustment >> Read notes, press “ENT” Turn off the ignition switch and then turn the ignition switch... Reading mileage... Confirm current mileage, press “ENT”>> Input the mileage of the adjustment: 110343 >> ENT Please turn off the ignition switch and then turn the ignition switch... Adjustment complete. The odometer turns to be 110343. Done! Using Obdstar X300M Cluster Calibrate Tool to do odometer correction for 2008 Mazda 6 successfully.
https://www.obd2shop.co.uk/ |
Archives
April 2024
Categories
All
|