Today I’m gonna show how to use Xhorse VVDI Prog&CGDI MB Tool to program a spare key for Mercedes Benz W169 A class when all keys lost. Tools Xhorse VVDI Prog CGDI MB Xhorse Benz EZS/EIS Adapters(W169/ST12 adapter) Mercedes W169 EIS A Mercedes Remote Key Read & Save Data Connect VVDI Prog, W169(ST12) adapter, EIS with computer on bench. Start VVDI Prog software, so we can check the connection diagram if we’re not sure. Select correct info on right side. Type: 4-IMMOBILIZER Brand: BENZ Chip: EIZ-W169-V1-ST12(ADAPTER) Click “Connection diagram”. Click “Read”. VVDI Prog starts reading and getting data... Operation success. Click “Save” to save the data file. Program Key Disconnect VVDI Prog, replace CGDI MB Programmer for connection. Start CGMB software, Load file >> Select data file >> Save EIS data >> Save >> Yes Save file successfully! The data now is on our CGDI MB Tool from EIZ, it’s already got password because we’ve read it directly from EIS. Generate key file >> Load EIS file >> Select data file saved >> Selected “VO51”, and one blank key position: 3 >> Generate Generate success, click “Save” to save file. Put a new smart key into CGDI MB key slot, Read/write key >> Open file/write >> OK >> Select generation file It starts writing automatically... Write success. If we read the key, it is with SSID and put into position 3. The key can start the vehicle now. Done! This is a quick demo on using Xhorse VVDI Prog + CGDI MB to program Mercedes W169 all keys lost on bench.
https://www.obd2shop.co.uk/
0 Comments
After replacing BCM, Nissan may have a fault code P1614. This code usually comes out when a not registered or damaged key is used to start the engine. Using Launch X431 V, X431 V+ or X431 Pro Mini can do an immobilizer NATS(Nissan Anti-theft System) key register for Nissan. Following we’re taking a 2014 Nissan Almera N17 to make a demo on how to do. Read Pin Codes Connect X431 scan tool into OBD, go to scan systems firstly, Local diagnose >> Nissan >> OK >> Manually select >> Far east >> Malaysia >> Almera >> N17 >> 11/2014 >> Health report Find out the fault code: P1614: CHAIN OF IMMU-KEY NATS(Nissan Anti-theft System) >> After replacing or installing operation >> Replace BCM This procedure erase all registered key Ids. Therefore, all of the customer’s keys should be obtained before starting this procedure. Press “OK” to continue. The immobilizer codes (PIN) were read out, press “OK”. Input immobilizer code(4 digits PIN) for initialization. OK >> OK Follow the instructions to operate: Insert ignition key into ignition key cylinder and turn it ON. The system will automatically proceed to initialization ECU after operation. Registration Key 1. Remove inserted ignition key from ignition key cylinder; 2. Insert unregistered ignition key into ignition key cylinder, turn it ON, wait for 5s or more; 3. Check that security indicator blinks 5 times; 4. Turn ignition switch to OFF, remove ignition key, wait for 3s or more; 5. A maximum of 5 ignition keys can be registered by repeating procedure from step2 to step4 using unregistered ignition keys. After key registration operation, they system returns to key registration mode. Therefore, it is necessary to end operation. 1. Insert ignition key into key cylinder and turn it to ON; 2. For models with remote control engine starter, buzzer of remote control engine starter sounds once. Registration unsuccessful if buzzer does not sound or sounds 3 times; 3. Turn ignition switch to OFF, remove ignition key, wait for 3s or more; 4. Check that security indicator blinks at intervals of approximately 3s. Once done, all keys can start the engine. Let’s check the DTC again. The fault code P1614 has cleared. Done! This is how to use Launch X431 Diagnostic Tool to do an immobilizer key register for Nissan after replacing BCM.
https://www.obd2shop.co.uk/ Autel MaxiIM IM608 is able to add a remote key for Suzuki Swift Dualjet 2020 success. Key type: 47 chip, frequency 433Mhz type B. Have been programmed remote, let’s go to add the key with Autel IM608. Plug connector into OBD2 port, turn on ignition with working key, press IMMO >> VIN >> Auto detect >> Manual selection >> Other >> Swift IMMO status scan >> BCM(8 digits) >> Add key(guided) Follow the notes to operate: Turn hazard on. Turn ignition on. Press “Start” to perform the function automatically. Step1. Read PIN Step2. PIN verification Step3. Key programming All keys will be erased, prepare all keys to program. Calculate PIN via online, press “Yes”. Turn ignition ON or force to ignition ON if all keys lost. It shows number of keys:1, press “Yes” to learn next one. Swift off, pull out the first key, turn on with next key. It shows 2 keys now, press “No” to finish. Learn keys success. Test the new key, its remote is fine, and can start the engine normally. Done! This is how to use Autel IM608 Key Programmer to add 47 chip remote key for Suzuki Swift Dualjet 2020 by OBD.
https://www.obd2shop.co.uk/ Having been replaced the dashboard, I’m gonna to use Obdstar X300M Odometer Correction Tool to adjust mileage for a Volkswagen Passat. Its kilometer on dashboard is 146021km. The procedure below works on Passat B6, B7 & CC. Connect X300M with OBD2 port via cable, press Vehicles >> Cluster calibrate >> VW >> Select from type >> NEC+24C64 >> Color meter >> Type 1(2013) >> Read write mileage Note: adjustment mileage may cause the EEPROM data to be destroyed, please backup the EEPROM data first. Turn on ignition first, if it is a smart key, please turn off ignition and then turn it on, press “ENT” to continue. Logging in system... Input the mileage of the adjustment: 220000, press “ENT”. Ensure the instrument in the black state. Finish. As you can see, the dashboard kilometer has changed, it is 220001 now. Done! More Cars Mileage Correction Tutorial:
VW Audi http://blog.obd2shop.co.uk/vw-audi-odometer-correction-via-obdstar-x300m-by-obd/ Mercedes E Class W212 2014 http://blog.obd2shop.co.uk/mercedes-e-class-w212-2014-odometer-adjustment-via-obdstar-x300m/ Hyundai Accent 2018 http://blog.obd2shop.co.uk/hyundai-accent2018-mileage-correction-via-obdstar-x300m/ This is using Obdstar X300M to make mileage adjustment for a VW Passat. It supports lots of car makers, for latest cars, please buy Obdstar ODO Master. https://www.obd2shop.co.uk/ There is a check engine warning light on the 2016 BMW 3 series dashboard, so I’m gonna use Autel MaxiCOM MK808 Scan Tool to diagnose its reason and reset it. I’ve got the MK808 plugged into OBD2 port. So let’s start, press Diagnostics >> BMW >> Manual selection >> 3 series >> F30/F31/F35 >> Yes Diagnostics >> Control unit >> Drive >> DDE(Engine-Diesel Electronics) >> Read codes The Autel MK808 is giving 2 fault codes: 25F500 - Intake Air Temperature(IAT) sensor signal; circuit open/short to battery(+) 28D600 - HFM(Hot Film Air Mass Meter) signal; circuit open/short to ground or positive terminal. If you don’t know what the codes meant, just put into Google, it’ll exactly tell how to do. There is a fault with the mass airflow sensor. In fact, I’ve taken that out, and put a new one in. But obviously the BMW is still getting 2 fault codes and a warning light. So I’ll escape back to erase codes. Erase code >> Yes >> OK Codes have been successfully erased. The check engine light has gone! Done! Autel MK808 Diagnostic Tool also does many other special functions like oil reset, EPB, SAS, TPMS, DPF, BMS...service for BMW and most of car makers. Its full system diagnoses helps me a lot for daily work.
https://www.obd2shop.co.uk/ |
Archives
April 2024
Categories
All
|