This post will guide you on how to use the Lonsdor K518PRO Programmer to modify and convert the LT-Series smart key Button Function.
The tools we need: K518 PRO LT-Series Smart key Procedure: Part 1. Modify LT-Series Button Function Take LT20-04 as an example. Choose [Special functions]>>[Key settings]>>[Lt smart key]>>[Read/Modify button function] Put in LT20 smart key. Please Note: 1. The key requires the battery installed properly. 2. Place the key horizontally on the card slot, easier to identify. Click [OK] to continue.
Then we set the buttons, as shown in the figure below, we set Button ③ from "Rear window" to "Trunk".
Set Button ④ from "Left sliding door" to "Panic". Click [OK] to continue. Conversion is successful.
Then we return to the previous interface and select [Read/Modify button function] again to check.
As shown in the figure, the previously set information has been successfully saved.
Part 2. Convert LT-Series Button Function
Take LT20-06 6 buttons as an example. Choose [Special functions]>>[Key settings]>>[Lt smart key]>>[Convert smart key type]. This function requires an internet connection. Push open the card slot's baffle on the device. Place the key to be generated into the card slot.
Choose [By selecting key type] >> [Generate 8A]
Frequencies and board numbers can be chosen freely.
Then we set the buttons, as shown in the figure below, we set Button ③ from "Hatch" to "Right sliding door".
Set Button ⑥ from "Right sliding door" to "Hatch". Click [OK] to continue. Generation successful.
Then we return to the previous interface and select [Read/Modify button function] to check.
As shown in the figure, the functions of Button ③ and Button ⑥ were successfully converted.
Note: The button functions of the original car key can be combined and set to the LT-series smart keys at will.
Video guides:
0 Comments
Today I'm going to program a new remote for 2023 GMC Savana with Lonsdor K518 PRO. Since I've already had the original working key and a new key at hand, let's get started.
Immo & remote >> GMC >> Savana >> Remote >> 2022-2023 >> Program remote Please switch the ignition ON. Within 1 minute hold down each remote lock and unlock buttons together, until the vehicle makes a sound, click "OK" to continue. Programming complete. Test the keys, both the original one and the new one are working. Done. Lonsdor K518 PRO, K518 series have upgraded FIAT vehicle coverage for reading immo data & making dealer key on April 23, 2024. Read this article to learn how to update K518 Fiat immo software & program new keys. Supported FIAT Car List: Grand Punto (2005-2014) 500 (2006-2017) Nemo (2007-2017) Bipper (2007-2017) Cinquecento (2007-2021) Mini Cargo (2008-2021) Qubo (2008-2021) Fiorino (2008-2021) New Fiorino (2008-2021) Punto (2009-2021) Punto Evo (2009-2021) Pratico (2010-2021) Doblo (2010-2021) Viaggio (2011-2018) Panda (2011-2021) 500C (2011-2021) Avventura (2014-2018) Egea (2018-2021) Tipo (2018-2021) Linea (2018-2021) 500X (2018-2021) 500E (2018-2021) New 500 (2020-2022) New 500C (2020-2022) How to program Fiat's new key with K518 PRO? 1. Read Immo Data Immo & remote >> FIAT >> Select from vehicle >> Europe >> 500 >> Mechanical key >> 2006-2017 >> 70F3633_93C86_46 >> Read immo data Check the immo data, and press "OK". Save the immo data file. Reading successful. Can use this data to make the dealer key and then the program key. Note: if vehicle communication fails during subsequent function execution, please disconnect the vehicle battery for 1-2 mins and re-connect it, then retry the function. 2. Make Dealer Key Make dealer key >> OK >> Selected immo data file >> OK Push open the card slot's baffle on the device. Place the key to be generated into the K518 PRO card slot. Operating to the key, please wait... The dealer key was generated and locked successfully. 3. Add New Key
Press the "Program key". This operation will delete all programmed keys, which need to be re-programmed before use, keys to be programmed need to be custom or dealer keys, press "OK" to continue. Please insert the key to be programmed, and switch the ignition ON. Enter PIN code. Programming succeed. Please switch the ignition off. Turn the ignition on. Current key count: 2 Programming complete. How to unlock genuine/OEM chip type 8A keys with Lonsdor K518 PRO? Read this article carefully to learn. Here is an original key for the Toyota Camry as an example. Read Key Special functions >> Identify/copy chip >> Identify/copy >> Identify/Copy Put chip to be identified into K518 PRO card slot. Press OK. We can find this key's chip type is 8A-A9, and the key is locked Unlock Key
Return back to the Home page. Special functions >> Unlock key >> Toyota smart key >> 8A >> Unlock Toyota smart key(8A) This function only supports unlocking Toyota 8A(39/88/A8/A9/AA/BA/F3) genuine/OEM smart keys. Note: please make sure the key battery is fully charged! Press OK. Please put the key into the K518PRO card slot. This operation will unlock the key(revert to brand new, un-programmed). Press OK to continue. Please confirm again that you need to unlock the genuine/OEM key! Press OK. The key unlocked successfully! Go back to identify the key again. The key is unlocked now. Done. This is a tutorial on how to convert the LT20 Smart Key type in Lonsdor K518 PRO. We'll need an original key for detecting first. Special Functions >> Key settings >> LT smart key >> Convert smart key type This function requires an Internet connection. Push open the card slot's baffle on the device. Place the key to be generated into the K518 PRO card slot. Press "OK". Selected "By identifying working key". Please place a working key into this K518 PRO card slot. In the frequency test, slowly take the LT20 smart key 20cm away from the card slot. Now we can see the frequency of the working key.
Current frequency: 433.58/434.42 MHz Select the frequency we just detected >> Choose the button type same as the working key Working key identification is complete. Please put the LT20 smart key back into the K518 PRO card slot to generate. Start to convert... Generated successfully. If the key has a remote but no smart function after key programming is successful, please enter the "Modify frequency" function menu to change. Done. How to obtain P1 P4 page data of the original car key with Lonsdor K518 PRO Key Programmer when all keys lost? Read this article to learn the new function. 1. Choose any data from "Immo & Remote" to generate the emergency key. Eg. Immo & Remote >> TOYOTA >> Select from type >> All smart key lost >> Type(2016-) >> BA >> Generate emergency key(LKE/PRO Antenna) This function can load backup data to generate an emergency key in an AKL situation, and then you use this key to turn on the dashboard to add keys. Press "OK". This function requires an Internet connection. Press "OK". Connect the K518 PRO antenna and place the antenna's top into the card slot >> Select the immo data file Emergency key generation is successful. 2. Obtain P1 P4 Page Data
Return back to the Home page. Special functions >> Identify/copy chip >> Identify/ Copy >> Identify/ Copy Put chip to be identified into K518 card slot. Now the last data obtained shows that page P4 is 8A-BA. Done. Lonsdor K518 PRO and K518 Series key programmer upgraded the auto immobilizer car list for BMW, Peugeot, and Chevrolet on April 9, 2024. Please update your device to check the details.
BMW BMW\EWS PEUGEOT General area\Boxer\2010-2023\Immobilizer General area\ION\2009-2019\Mechanical key Europe\Boxer\2010-2023\Immobilizer Europe\ION\2009-2019\Mechanical key South America\Boxer\2010-2023\Immobilizer CHERY Chery\Explore series\Explore 06\2023- Tiggo series\Tiggo 9\2023- Fulwin series\Fulwin A8\2024-
This post will introduce you to how to copy an access card using Lonsdor K518 Pro.
Firstly, we can choose [Access Card], it also can be chosen from [Special Functions]. Then select [Copy Access Card]>>[IC/ID Card].
Put the access control card in the card slot and click OK.
Please wait... Now we have identified the information of the access card, click "OK" to continue.
Decoding...
You can take away the key now. Decryption is successful.
Then we choose [Copy] and put the new chip into the card slot.
Please wait... Copy scucceed!
The above is the whole process of using the Lonsdor K518 Pro copy access card. Stay tuned for more technical services.
http://blog.obd2shop.co.uk/ Video guides: The 2024 New Lonsdor KW100 Accessory pre-order is available now. Supports quick identify Toyota/Lexus smart key in key adding or all keys lost situations. Quick generation for Lonsdor LT20 Smart Keys. Functions Generate smart key Detect remote frequency Detect frequency sequence Modify frequency Get version info Unlock key Read button function Modify button type Upgrade key Identify chip Modify remote count value Parameters Product dimension 120*70*20mm Carton size17*13.5*4, Carton size22*14.5*8.5mm Communication method Bluetooth 5.0 Application 1. Included a standard cable for power supply. 2. On one end connect to a smartphone or DC5V output, and connect to the KW100 on the other end. How to use Lonsdor KW100? Here's using Lonsdor KW100 to quickly generate the 2016 Toyota Crown smart key in key adding/AKL situation for example. Key Adding Situation Here we have an original key and a new LT20 smart key. Connect KW100 & smartphone, and open the Lonsdor app: KW100 >> Quick generation >> Quick generate(with key) >> Start If the key cannot be identified, please slowly take it 15-20 cm away from the identification area, the detection will take time, so please wait... Acquired successfully. It shows the key type and frequency. Put an LT20 smart key(with battery) into the KW100 card slot. Continue >> Select button >> Start to generate >> OK Wait KW100 processed until 100%... Generation successful. All Keys Lost Situation The car is locked and the original key is out of the car. Open the door to start. KW100 >> Quick generation >> Quick generate(AKL) >> Start Please step on the brake, and press Start button every 5s. This function will take about 1-3 mins, Please wait properly... Acquired successfully. We can see the key type and frequency already. Put an LT20 smart key(with battery) into the KW100 card slot. Continue >> Select button >> Start to generate >> OK Wait KW100 processed until 100%... Generation successful. Then we can use Lonsdor K518 PRO to finish the key programming. Lonsdor quick generate is the fastest way ever, to detect key information of vehicles and generate smart keys. Pre-order now to enjoy instant access to convenience and efficiency in the Lonsdor LT20 key generation.
https://www.obd2shop.co.uk/wholesale/lonsdor-kw100.html Contact info: Email: [email protected] Whatsapp: +86 13983755934 Telephone: +86 13983755934 WeChat: +86 13983755934 Skype: OBD2tool.co.uk Here I'll introduce the edit data and Bluetooth transmission function of Lonsdor K518 PRO. Read this article carefully to learn the new function. How to Edit Data with Lonsdor K518 PRO? Edit data >> Open file >> Select the backup data file >> Edit data Here we can edit data files as needed. How to use Bluetooth Transmission with Lonsdor K518 PRO?
1. Settings >> Bluetooth settings >> Turn on Bluetooth 2. Open the phone and search for K518 PRO, click pair to start the connection 3. File manager >> Selected and long press the file >> Share Now we can start transferring the file to the phone. It's also possible to transfer mobile phone files to K518PRO via Bluetooth. |
Archives
April 2024
Categories
All
|