This is a tutorial on how to use Launch X431 ECU & TCU Programmer to clone VW ME17.5.22 ECU on bench. You can also use the X-Prog3 + PC Adapter to finish the same job. Simple operation with 3 steps only. Open X431 ECU & TCU Programmer software to search the ECU model: Skoda, Fabia 2006-2020, CWVA 1600 MPI 110, ME17.5.22 TC1724F Click "Direct connection of diagram" to find the wiring diagram. Step1. Save original EEPROM & FLASH data. After the connection is successful, click "Read chip ID". Read EEPROM data >> Save EEPROM data file. Read FLASH data >> Save FLASH data file. Click "Disconnect". Step2. After reading the original computer and the new computer data firstly, you need to clone the data and then write the cloned data in. Back to the previous interface, Data processing >> Data cloning >> VW MEDC17 clone >> Load the FLASH file of the original ECU >> Load the EEPROM file of the original ECU >> Load the FLASH file of the external ECU >> Load the EEPROM file of the external ECU Clone data was generated successfully, please save the file! Step3. Save the cloned EEPROM data and write it back to the new ECU.
Read Chip ID >> Write EEPROM data >> Load the cloned EEPROM file Data is successfully written. Write FLASH data >> Load the original car FLASH data restoration Data is successfully written. Click "Disconnect". Completed.
0 Comments
Now, Lonsdor K518 series has been updated to support OBD programming for Chery vehicles. Read on to find out more details.
Support Models: EXEED LX LX (ETI) RX JETOUR Dashing CHERY E3 E5 EO1 EO5 Chery A15 Tiggo 3 Tiggo 5 Tiggo 5X Tiggo 7 Tiggo 8 Tiggo e Tiggo Facelift Arrizo 5 Arrizo 5E Arrizo 7 Arrizo 7E Arrizo e Fulwin 2 Arrizo GX Arrizo M7 ArrizoM7(PHEV) KARRY Riich K50 K50S K60 K70 COWIN C3 C3R E3 V3 X3 X5 Please update your device for the details. New Yanhua Mini ACDP Module 31 for BMW F chassis BDC IMMO via OBD is coming, need to work with Mini ACDP-1 or Mini ACDP-2 basic module. Module 31 Functions: 1. Exclusively supports 2 methods to preprocess BDC: OBD CAN & OBD DoIP; 2. Supports BMW F chassis BDC key programming & mileage reset via OBD. Module 31 Features: 1. Fully OBD operation, no need to disassemble or assemble the BDC module, no risk of dismantling the BDC or damaging the 95256 chip. 2. DoIP protocol preprocessing only takes tens of seconds, fast, safe, and stable. How to use the OBD CAN Method? 1. Connect Mini ACDP or Mini ACDP + DoIP adapter to OBD; 2. Connect Mini ACDP-2 + OBD adapter or Mini ACDP-2 + OBD extension cable to OBD. How to use the OBD DoIP method? 1. Connect Mini ACDP + DoIP adapter to OBD; 2. Connect Mini ACDP-2 + DoIP adapter to OBD; Note:
1. Please ensure the connection is good and the vehicle has enough battery voltage. 2. Please DO NOT cut off the power or pull out the device during the operation. www.obd2shop.co.uk Xhorse has released a new VVDI Key Tool Plus VA version, focused on VAG IMMO programming like Volkswagen, Audi, Porsche, etc. What's it different from the Key Tool Plus advanced version? Here we have the comparison table. Comparison Table Conclusion
Xhorse VVDI Key Tool Plus VA price is half cheaper and it does not have BMW & Mercedes-Benz IMMO programming function that requires additional activation. Other than that, everything else is the same. www.obd2shop.co.uk Good news!!! The Lonsdor K518 series has been updated to be able to support programming via OBD and add keys without PIN codes for the latest Ford/Lincoln vehicles (2022-). Please read on to figure out more details.
Support Models: Ford (USA) Edge(2020-) Mustang(2020-) Explorer(2020-) Transit(2020-2021) F-250 Raptor(2020-2022) F-350 Raptor(2020-2022) F-Series Super Duty(2020-) Expedition(2020-2021) Ford (Europe) Transit(2020-2021) Ford (South America) Transit(2020-2021) Lincoln Aviator(2020-) Nautilus(2020-) Navigator(2020-2021) Please update your device for the details.
Yanhua has announced the first generation of the Mini ACDP device was disabled. What to do after purchasing the Transfer License service? Here we offer 2 methods to help transfer the license to Mini ACDP 2.
Read also What's Yanhua Mini ACDP Transfer License Plan A & Plan B? Method 1. Transfer by Yanhua Provide the back photo of both devices to the online service, Yanhua factory will help to transfer all licenses. Customers can use ACDP-2 directly without any operation. Method2. Transfer by Yourself Check the video to learn:
1. Send the SN of both devices to the dealer or manufacturer to obtain an authorization transfer code.
2. Open Mini ACDP app >> Me >> About, make sure the Android version is 3.0.107 or newer/ IOD version is 3.1.0 or newer.
3. Power on the Mini ACDP 1 and make sure the ACDP is bound.
4. Me >> License Transfer >> Transfer >> Enter the authorized transfer code obtained and SN of the new Mini ACDP 2 >> Submit The authorization share is successful, please connect device ACDP2-E901C to confirm! This post will show you how to use Autel MaxiIM IM608 Pro 2 to program a key for your 2022 Hyundai Sonata when all keys are lost. Here is the procedure: Select "IMMO" >> "Hyundai" >>"Manual selection" >> "America" >> "SONATA(DN8)" >> "2021-2022" >> "Smart Key". Vehicle information is displayed as shown below: Then we choose "Control unit" >> "Keyless System" >> "Remote control learning" >>"Smart key learning". The following message appears on the IM608 PRO 2 tablet: This function supports adding keys and all keys lost. Performing this function will erase all existing keys, all the old keys must be relearned again to be able to use normally, whether to continue? We choose "Yes" to continue. Turn the ignition off (note: the instrument screen is black). Open and then close the driver's door once! Then we need to enter the PIN: Please enter the 6-digit security code: This function may be limited if the PIN code is entered incorrectly three times. After making sure that the PIN code is entered correctly, we select "Yes" to continue and then we start to do smart key learning. Confirm if the key sensing area of the vehicle is the ignition switch. Note: For a small number of vehicle models, the key sensing area is not the ignition switch but maybe another position such as the cup holder. After pressing OK, perform the operation below: Within 5 s, press the Start/Stop button with the smart key with its back or top against the button for 5 s. Then the security lamp will flash. Programming succeeded.
Would you like to program the next one? We choose" No" to continue. Number of current keys: 1 Please exit the system to the vehicle selection menu and check if the key is programmed successfully. As we know, the new Yanhua Mini ACDP 2 has been coming out to replace ACDP1, which will require users to transfer all licenses for continuous service. ACDP-2 License Transfer Plan can help to solve the problem. Therefore, it offers 2 options for choice: 1. Plan A-License Transfers Plan A allows to transfer of all licenses from ACDP-1 to ACDP-2, which means to delete ACDP-1(ACDP-1 CANNOT be used anymore). Cost 2. Plan B-Shared License Plan B can share all ACDP-1 licenses with ACDP-2, which means both devices can be used at the same time after sharing the license. Notice: In case you buy a new module after sharing the plan, this new module license only can be used on ONE module. The cost will be 35% of the total amount of the shared module's official price. Please send your ACDP-1 SN(backside of the device) to the manufacturer or distributor to check the exact price. *Both plans need to buy the ACDP-2 Basic Module first. At present, most Yanhua modules are common, no need to re-purchase any new modules. Just take note of below:
1. It needs to cut the protruding part when using module 18/19/25/30 for Mini ACDP 2; 2. Module 3/8/12 can be used directly for Mini ACDP 2. This post will show you how to program a key (all key lost) for a 2020 Honda CR-V using Autel KM100. Here is the procedure: Click "IMMO", choose "Honda">>"Manual selection">>"CR-V">>"Smart key">>"Push to start". Then choose "Control unit">>"Keyless System(Honda) It appears "Is the ignition turned on by pressing the Start button twice?" Does not, we choose "No" to continue. Press and hold the stop button. The ignition is switched on, then release the engine start/stop switch. Establishing vehicle communication... Choose "All keys lost". Turn the ignition switch off. (Don't press the foot brake and press the engine start/stop button.) Place a key to be learned in the vehicle and take all other keys out of the vehicle to a place more than 5 m away. "Is the ignition turned on by pressing the Start button twice?" Does not, we choose "No" to continue. Press and hold the stop button. The ignition is switched on, then release the engine start/stop switch. Establishing vehicle communication... It appears "Is it a new model (Generally refers to the model after 2020)?" Choose"NO" to continue. Establishing vehicle communication... "How many keyless access remotes do you want to keep?" We just want to do one, enter "1" then click "OK" to continue. Please turn the ignition switch off. (Don't press the foot brake and press the engine start/stop button.)
Please turn the ignition switch on. (Don't press the foot brake and press the engine start/stop button twice.) Are both the keyless access and immobilizer indicator lights turned off? Choose "Yes" to continue. Then follow the instructions of the KM100 tool and repeat the above operations again. Vehicle condition checking, Please wait. The registration is completed. Please turn the ignition switch off. (Don't press the foot brake and press the engine start/stop button.) Check all keyless access remotes to ensure each will start the engine. Check all keyless access remotes to ensure each will lock and unlock the doors. This is a quick guide on how to use the OBDSTAR DC706 ECU Tool to clone BMW MSV90 ECM on bench. Besides, it also supports clone MEVD17.2.6 EXX, MEVD17.2.6 FXX, MSD80, MSD85, and MSD54 ECM. For details please refer to the below chart. BMW ECM Support List: Tools Required OBDSTAR DC706 Main cable P004 Adapter + P004 ECU Clone Jumper BMW MSV90 ECM Please keep DC706 charging & communicating throughout the whole process. Operation Process ECU Flasher >> ECM >> Latest version >> BMW >> BMW Continental MSV90 TC1796(BENCH) >> Start This function is available by connecting the server, please ensure the Internet connection is normal. Remarks: Click operation instructions at the bottom left to check the best detection method.
Connecting the harness according to the wiring diagram. Follow the interface prompts: Switch the ignition off. Switch the ignition on. Read INT eeprom, INT flash(TC1796), Maps, and ISN code. Please check the log on the left side screen to see the saved path of reading data. After successfully saving, write INT eeprom, INT flash(TC1796), and Maps. The ECU clone operation is completed. Remember to disconnect before exiting. |
Archives
April 2024
Categories
All
|