This post will guide you on how to use the Autel MaxiIM IM608 PRO 2 key programmer to add a new key for the 2011 Volkswagen GTI. The tools we need: Autel IM608 Pro 2 Autel X400 PRO A Volkswagen GTI working key A new blank key First, take the original key set it into the ignition, and turn the ignition on. Then select IMMO on the IM608 Pro 2 tablet. Select "Volkswagen" >> "Smart selection", confirm the vehicle information, and click "Yes" to continue. After coming to the following interface, select "Add Key", then click "Yes" to continue. Next are the three operations of "Add key". 1. Read IMMO data 2. Make dealer key Do you want to generate a dealer key? Click "Yes". Then place a blank key into the key slot of the programmer and press OK. The dealer key was generated successfully. 3. Add keys to the vehicle Place the dealer key into the key slot of the programmer Entering programming mode. It may take a long time... Key added successfully. Then go back to the "Function selection" interface and select "Add remote control". Press the unlock button on the door, then choose "OK" to continue. Press any button of the key within 10s. Remote control adding succeeded. Let's test everything out, turn the ignition off, pull out the original key, and then insert the new key. The car starts and runs with the new key! Tech support: www.obd2shop.co.uk
0 Comments
Lonsdor K518 series has supported all keys lost and added new keys with a free PIN code via OBD for Mazda's new models after 2019. Like Mazda 3, Mazda 6, XC-5, CX-9, XC30. Here's programming the 2020 Mazda 3 all keys lost with Lonsdor K518ISE as an example. We'll simulate the situation for this car. Let's strap the K518 device to the steering wheel for convenience to operate. Immo & remote >> Mazda >> China >> Axela >> 2020- >> All smart key lost * This function requires a WiFi connection, please confirm WiFi is well connected. Warning Please use the specific key to the program. After the programming is complete, some aftermarket keys can start the car, but the dashboard's fault light will go on and the fault code can't be cleared. Press "OK" to continue. Note: All smart keys will be deleted, at least 2 keys are required to complete programming. If the vehicle alarm rings, please wait about 30s for the alarm to end. Click "OK" to continue. (For all key lost, this car will be in the alarm situation, you'll need to wait for 30s until the alarm to end. For the simulation, we don't need to wait for this time.) All the smart keys must be kept 1m away from the car. Press and hold the start button for 10s, and then press the start button once the button indicator turns from green to yellow. If the vehicle alarm rings, please wait about 30s for the alarm to end. Press "OK". It takes 7 minutes to grant security access, and the buzzer will beep after 7 minutes... (We can hear the horn rings, which means we have already got security access.) Count of current smart keys: 2 Press "OK". Delete all keys successfully. Please switch the ignition off.
Note: 1. Turn ignition on. 2. When the start button's indicator light turns green(in 5s), hold the key's logo end near the button. Current key count:1 Press "OK" to program the next key. Repeat the operation as before... Current key count: 3 Press "Cancel" to complete. Before starting the car engine, you will need to complete the below operation steps: For AT vehicles 1. Slam on the brake. 2. In turn to put each programmed key onto the car start button to start the engine for 3s, then turn the ignition off. Test all 3 keys, lock and unlock OK, start car OK. This is how to program the 2020 Mazda 3 with all keys lost with Lonsdor K518 by OBD successfully. Launch x431 key programmer specializes in reading and writing key information, generating various key chips, etc. Currently, it can only be used with X431 IMMO Elite, X431 IMMO Plus, X431 PAD V (PAD 5), and X431 PAD VII (PAD 7). How to use the x431 key programmer? 1. Use with Super Chips On the tablet (this item uses PAD V as an example), open the X431 PAD V APP, select "Other Modules" >> "Toolbox" >> "Key Programming" Enter the "Set Super Chip Type" menu to generate. Select the corresponding key chip type and insert the super chip into the anti-theft induction coil. Once successfully generated, it can be used. 2. Use with Super Remotes Take LS Nissan super remote as an example: The initial operation is the same as the super chip, enter the "Key Programming" menu and select "Vehicle Remote", then select the corresponding smart key model to generate. Place the electronic remote key in the key programmer to generate. For car models without electronic keys, enter "Set type of wireless remote" to generate the corresponding key. For more information about Launch X431 Key Programmer, please click https://www.obd2shop.co.uk/wholesale/launch-x431-key-programmer.html
This is a tutorial on how to use Launch X431 G3 + X-PROG PC Adapter to clone Volkswagen MED17.5.25 ECU on bench. By connecting with the PC adapter, G3 can work as X431 ECU & TCU Programmer to read and write ECU data. Read also: Launch X-431 ECU & TCU Programmer vs. GIII X-PROG3 Connection 1. Open X-PROG3 PC Adaptor software, enter ECU model to search, and select: Volkswagen(VW), Beetle 2011-2017, CYVD 1197 104, MED17.5.25 TC1782F 320 2. Click "Direct connection of diagram" to get the wiring diagram for the connection. Procedure 1. Backup Original ECU Data Click "Read chip ID". Read EEPROM data >> Save EEPROM data file Read FLASH data >> Save FLASH data Disconnect. 2. Data Processing Go back to the previous interface Data processing >> Data cloning >> VW MEDC17 clone >> Load the FALSH file of the original ECU >> Load the EEPROM file of the original ECU >> Load the FLASH file of the external ECU >> Load the EEPROM file of the external ECU Clone data was generated successfully. Save the cloned EEPROM data and write it back to the new ECU. 3. Write to the New ECU
Click "Read chip ID" again. Write EEPROM data >> Selected the cloned ECU data file Write FLASH data >> Select the original car FLASH data restoration Disconnect. This post will guide you on how to register Yanhua Mini ACDP2 APP. Step 1. Open the ACDP2 APP, select "Me", then click "Login". Step 2. When you enter the following interface, click "Register" to register. Step 3. Complete the options marked with red *, then choose one of the four registration methods below to complete the registration. Note: If you use one of the registration methods and get an error during the registration process, please try another method again. If the error persists, contact the seller. Step 4. Once the registration is complete, come back and log in.
Autel MaxiIM IM508 + OBDSTAR Toyota-30 Cable can program a new proximity key for the 2023 Toyota Prius without a pincode. OBDSTAR Toyota Cable is designed as a 30PIN connector for 4A, 8A-BA immo key programming. Not only compatible with OBDSTAR X300 DP PLUS or X300 PRO4, but also works for other key programmers like Autel. Read also OBDSTAR Toyota-30 Cable for 4A/8A-BA IMMO Upgrade Connection It's very easy, just popping that lower dash panel, reaching up in there unplugging it. Then plug the Toyota-30 Cable into the 30PIN port. Connect the other end to Autel IM508. Procedure Step1. Back-Up IMMO Data This function is used to back up EEPROM data of the smart main ECU, which can be used to perform IMMO related functions without PIN. This function supports models with 8A-BA smart key as of 2022(equipped with TMLF19D smart main ECU). Click "Yes" to continue. Ensure the network connection of the device is good. Turn off the ignition, and turn the hazard warning light on and off once. Reading EEPROM data... Backup succeed. Step2. Add Smart Key
Add Smart Key >> Start This function serves to learn keys. Please complete the steps within the specified time. Turn the ignition on. Confirm VIN. Have you backed up the EEPROM data of this vehicle? Yes Select the saved EEPROM data. Keep a learned key close to the start button. Keep a new key close to the start button. Learning succeeded. Lonsdor K518 series has been upgraded to be able to program add key & all key lost without PIN code for the latest (2022-) Toyota/Lexus 8A-BA vehicles. Covering BZ4X, Granvia, Harrier, Venza, Sienna, Wildlander, Sequoia, Tundra, and Land Cruiser. Requirements 1. Need to activate Toyota AKL Online Calculation first and use Lonsdor FP-30 Cable together. 2. Working for Lonsdor K518ISE/ K518S Key Programmer. 2022+ Toyota 4A IMMO Upgrade We know the system of the latest Corolla Cross is different from the latest Sienna, it's a 4A chip vehicle. There's another good news today: Lonsdor K518 can program add keys & all key lost without PIN code on the latest Toyota 4A chip type vehicles, including Yaris, Cross, Frontlander, and Yaris HV(2022-). Operation Process Here's programming a 2023 Toyota Corolla Cross as an example. Preparation 1. Before doing this function, we need to connect the Lonsdor's latest Toyota FP30 Cable to a smart box of the car. 2. The other end connects to the OBD port of K518. *FP-30 will not damage the communication cable of the original car during operation. 3. In addition, we also need a Lonsdor LKE Key Emulator. Step1. Back-Up Immo Data
Please make sure the device is well connected to the network before the operation! During the use of this function, please do not operate abnormally, or maliciously steal relevant data, otherwise, the K518 will be locked and cannot be unlocked. Please turn the ignition on, if fails, please turn on 2 flashing lights. Immo data backed up successfully. Step2. Generate Emergency Key This function can load immo backup data to generate an emergency key in an AKL situation, then you use this key to turn on the dashboard to add keys. Please put the key emulator into K518's card slot. Selected the saved immo file. Generating... An emergency key was generated successfully. Please use the emergency key to turn the ignition on, then enter the "Add Smart Key" function menu to add new keys. Test the emergency key, it's working. OBDSTAR has released airbag reset upgrade V30.46 on 11th, Aug. Added 275 part no. again, 8800+ part no. supported in total. Now it's available on OBDSTAR X300 DP PLUS & OBDSTAR P50. Add 231 part numbers to support airbag reset: Add ACURA 95640 (1 part No.); Add ALFAROMEO 95256, 95640 (2 part No.); Add ASTON MARTIN (1 part No.); Add BAIC R7F701008 (4 part No.); Add BRILLIANCE R7F701008 (5 part No.); Add CHEVROLET R7F7010083 (3 part No.); Add CITROEN 95320 (1 part No.); Add DODGE 95256 (1 part No.); Add FORD 95320, MAC7242, TC22XX-16F (4 part No.); Add GREAT WALL XC2336A (1 part No.); Add HAIMA R7F701008(5 part no.); Add HONDA 95640, SPC56AP54, TC23XX32F (8 part No.); Add HONGQI R7F701008, R7F701009 (5 part No.); Add HYUNDAI 95256, 95512, TC23XX-16F, TC23XX-32F (9 part No.); Add INFINITI 93C76, 95640 (3 part no.); Add JEEP 95512 (2 part No.); Add KIA 95512 (1 part No.); Add MAZDA XC2361A (1 part No.); Add NISSAN 95128, TC22XX-16F (9 part No.); Add OPEL 95160 (1 part No.); Add PEUGEOT XC2336B-40F (1 part No.); Add RENAULT 95080, 95160, R7F701042, TC222A-16F (92 part No.); Add SEAT TC22XX-16F (1 part No.); Add SUBARU H8SX1726 (1 part No.); Add TOYOTA H8SX172X, R7F7016443, R7F7016843 (60 part No.); R7F7016443 (40 part No.): R7F7016843 (19 part No.): Add VW MPC5604P, TC224L-16F(2 part No.);
Add ZOTYE R7F701008 (7 part No.); Add 44 part numbers to support read/erase DTC: Add AUDI 95640 (2 part No.); Add BAOJUN TMS570 (1 part No.); Add CHANGAN R7F701A033 (1 part No.); Add DODGE 95128 (5 part No.); Add FIAT 95640, TC23XX-32F (23 part No.); Add GEELY XC2336B-40F (1 part No.); Add JAGUAR 9S12DT128 (5 part No.); Add SUBARU R7F7016863 (5 part No.); Add VW R7F701071 (1 part No.). Lonsdor LT20 smart key family has 8 different shapes to fit the original shell perfectly. Among them, Lonsdor LT20-01, LT20-04, and LT20-08 are the best sellers. This is LT20-01 with the same board shape as an original keyboard. It's not a problem to fit the original key shells for chip 4D. This model can be used to generate the key like Toyota Camry and Land Cruiser. LT20-04 is with a board shape to fit the key shells for chip 8A. Its original software is 0020. You can convert the software depending on the model and year of your car. It does a great job, like Toyota RAV4, Highlander. LT20-08 board shape fits the key shells for chip 8A as well. It supports software 0410. And can be used for many new Toyota models like the year 2022 Camry, Highlander, C-HR, and Avalon. All 8 different board shapes can be generated with different software with specific frequencies and button functions. How to generate LT20 smart key? We'll need Lonsdor K518ISE or KH100+ to process. The operation path is the same for both devices. Here's taking K518ISE and LT20-04 smart key to generate a new key for the 2022 Toyota Camry as an example. Please remember to set WIFI before key generating. Special function >> Key settings >> LT smart key >> Convert smart key type >> OK Push open the card slot's baffle on the device. Place the key to be generated into the K518 card slot. By selecting key type >> Generate 8A >> 0410(P4: 91 00 A9 A9) >> 433.58/434.42MHz >> Button 3 Trunk-Button 4 Panic Generate successfully. How to make a new LT20 smart key?
IMMO & Remote >> Toyota >> Select from type >> PEPS(passive entry and the passive start) >> Type3(CAN) >> Add smart key Make sure the smart key battery is full. Insufficient power may cause program failure. Put an emulator key or workable original key close to the ignition switch, and turn it ON till the dashboard is lit up. Current key count: 1 Put the back side of the registered key close to the start button, when the buzzer rings once, remove the key. Within 30 secs put the back of the key(to be registered) close to the car start button, when the buzzer beeps twice, remove the key. Operation completed! Count of registered keys: 2 Count of registrable keys: 5 Let's try whether is the new key working or not. We can lock and unlock the door. Done. OBDSTAR X300 DP Plus has released a major update on Toyota IMMO, stay updated with OBDSTAR software to get the latest features.
Highlights Added: Add 8A-BA type proximity read immo data, make a simulated card (key sim), add keys, erase keys, current number of keys, reset key ECU (all key lost), program ECU, program ID box with steering lock, remote engine start, etc. Functions for the below models: BZ4X 2022- RAV4 PHV 2022- GRANVIA HV 2022- SIENNA HV2022- HARRIER 2022- (MXUA80) VENZA HV 2022- HARRIER HV 2022-(AXUH8#) WILDLANDER PHV 2022- |
Archives
April 2024
Categories
All
|