Now I'm working on a 2014 Toyota RAV4 with all keys lost. Next, I'm gonna use the Autel MaxiIM IM608 PRO II to program a new blade key for this car. IMMO >> Auto VIN >> Toyota >> OK >> OK >> Control unit >> Immobilizer(H 8A/8E) >> Immobilizer reset(all keys lost) This function is only supported for the Middle East and the USA now. Ensure that the door remains open during the learning process.
Enter the number of keys to be registered: 1 Turn the ignition off. Turn the ignition on. Turn the ignition off and remove the key. Turn the ignition on. Turn the ignition off and remove the key. Follow the following steps to learn 1 master key within 120s: 1)Insert the master key, turn the ignition on, and wait for 5s. Then quickly turn the ignition on and back off 5 times until the SECURITY lamp goes out, which indicates that learning is completed. Test the new key, it can start the engine normally. Done. This is using Autel IM608 Pro2 to program the 2014 Toyota RAV4 with all keys lost successfully.
0 Comments
Today I'm working on a 2018 Hyundai Sonata with all keys lost. It's a push-to-start vehicle. Following I'm gonna try if the Autel MaxiIM IM608 PRO II + Xhorse XM38 Universal Key can be successfully programmed for this car. As we know, the Autel only supports to program IKEY Universal Key in normal. Anyway, let's start the test. IMMO >> Accept >> Hyundai >> Manual selection >> America >> SONATA(LFA) >> 2016-2019 >> Smart key >> OK >> Control unit >> Read immobilizer password >> Read Pin code(8A smart card) This function only supports models with 8A chip-type smart cards. Please ensure the key type is correct! Turn the Hazard warning light on. Turn the ignition off(note: the instrument screen is black). Open and then close the driver's door once! Reading password... Autel IM608 II gives the pin code: 138729 Keyless system >> Remote control learning >> Smart key learning
This function supports adding key and all keys lost; Performing this function will erase all existing keys, all the old keys must be relearned again to be able to be used normally, press "Yes" to continue. Turn the Hazard warning light on. Turn the ignition off(note: the instrument screen is black). Open and then close the driver's door once! Please enter the 6-digit security code: 138729 Note! Click OK to complete the following steps: Within 5s after OK is pressed, use the back or top of the smart key to hold down the START button for 5s until the anti-theft lamp flashes. (If the operation fails with the prompts, please remove the key case and re-execute the above steps so that the key chip can be successfully programmed.) Programming succeeded. Press "No" to complete. Number of current keys: 1 Please exit the system to the vehicle selection menu and check if the key is programmed successfully. Test the new key, it can work normally. Customer problem: My KM100 recently had this error, and some vehicles cannot be entered at all, such as Fiat-Bmw, how should I solve it? Solution: Enter the Data Manager menu and remove vehicles.
Then delete the software and go to update and download it again. For more tech support, please contact: www.obd2shop.co.uk Today I'm working on a 2020 Toyota Camry with all smart keys lost. It's a push-to-start vehicle. Next, I'm gonna use the Autel MaxiIM IM608 PRO II to program an Xhorse XM38 Smart Key for this car. Step1. Backup IMMO Data IMMO >> Accept >> Toyota >> Manual selection >> USA >> CAMRY >> 2012-2020 >> Smart key >> OK >> Control unit >> Keyless system >> Keyless system(CAN) >> Back up IMMO data >> Back up IMMO data(OBD) Ensure that the network connection of the device is good. Turn the ignition off, and turn the hazard warning lamps on and off once. This function is used to back up the EEPROM data of the smart box of the vehicle. The data can be used to generate the simulator key for the emergency start of the vehicle to perform the key-matching function. Warning: You must turn off the Bluetooth function of the device and connect VCI to Autel IM608 Pro2 with a USB cable. Otherwise, the function may fail! Turn the hazard warning lamps on and off once. Reading EEPROM data... Save the EEPROM file. Step2. Generate Analog Key Generate analog key >> Select the backup EEPROM file Key type: SLK4 Plug APB112 Smart Key Simulator into IM608S II tablet. Generate analog key complete! Note: The analog key must be powered on, never cut off! Please close the analog key to the push start(Start/Stop) button and press the start(Start/Stop) button. If the instrument lights up successfully, click "Yes" to continue. If the instrument fails to light up, click "No" to continue generating the next analog key. Generate analog key successfully! Step3. Add Key
Press "Add smart key". Do you want to use the simulator key APB112? Yes Notice: Each step must be completed within the specified time. If you have the original key, please connect the programmer and put the original key into the key recognition area of a programmer. Press "Skip". The positions for learning include: 5 Please put the analog key close to the START button. Put the XM38 Toyota key close to the START button. Registering, please wait... Learning succeeded. Test the new key, start the car OK, and lock and unlock OK. Done. Customer Problem: My IM608 II, VCI keeps displaying the "Unable to connect" message. There is no problem with USB, but Bluetooth can't connect normally. What should I do? Solution: Try to update the JVCI+ OS version. Step 1. Download the PC suites from the Autel website with the following link: https://download1.auteltech.net/Download/PCSuite/MaxiPCSuit/V1.40/MaxiPCSuite_V1.40.zip Please note that the PC suites are just for the JVCI+ driver, install the PC suites. For the PC can recognize the JVCI+. Step 2. Download the following zip file then unzip it. The link to the zipped file of VICupdate: https://we.tl/t-veC39XRaBW Run the following device upgrade exe file. Step 3. Select the JVCI+ and click on "确定"(confirm), after that, click on the bottom left button"检测设备"(detect device), then click on "开始升级" to start the upgrade of the OS of JVCI+. After JVCI+ has been upgraded, then test the tablet again with Bluetooth to see if the Bluetooth connection is back to normal again.
For more technical services please follow: www.obd2shop.co.uk If you encounter network errors like "Network unavailable. Error code: 1008", changing these settings should fix the problem, this post will guide you on how to adjust network settings on the Autel KM100 Key Tool. Here is the procedure: 1. Choose [Settings]>>[System Settings]>>[More]>>[Network & Internet], then click [Wi-Fi], tap the Wi-Fi you are connected to and we can see a little pen up here in the top right corner. 2. Click this pen, then click [Advanced Options], scroll down, and go to change IP settings: from "DHCP" to "Static". Then we scroll down and make sure [DNS 1] is "8.8.8.8", if not, just delete what's in there and make sure it says "8.8.8.8", then let's click "Save". 3. Reboot the KM100
It is very important to reboot your device after making such network changes. Click and hold the Power button, then click "Reboot" to restart the key tool. This post is about how to adjust the network settings in the Autel IM608/IM508 tablets. If you are facing errors like Unable to get server address Error: 1008, Unstable network, Network busy, Unable to access updates, etc. Changing these settings should resolve the issue. So here's the procedure: Go to the Home button at the bottom left of the screen and select [System Settings]. So you see we are connected to Wi-Fi, we will click and hold the Wi-Fi we are connected to, in the top menu click and hold, and choose [Modify Network]. We'll simply press the down arrow to hide the keyboard and choose [Show advanced options]. Now look where it says [IP Settings]: DHCP, so we change it to [Static]. Scroll down and the only thing we need to change is [DNS 1], we'll delete what's in there and it should default to this 8.8.8.8. Once again we will hide the keyboard and click [Save]. After saving these settings, we will reboot the tablet. Then press and hold the power bar at the top, then choose [Reboot]. The above is the entire process of adjusting the network settings in the Autel IM608/IM508 tablets. Once the setting is complete, remember to reboot, and let the network settings and the changes that we've made take effect.
For more technical support please visit www.obd2shop.co.uk This post shows you how to use Autel KM100 to add an ID4D 67/68 transponder key for Lexus RX350 2004. First, we select "IMMO", then enter "Lexus" in the search bar, select "Lexus", then select "Manual selection">>"Europe">>"RX350">>"Blade Key", select "Yes" to continue. Select "Hot function">>"Immobilizer(4D 67/68)">>"Key learning(guided)" Step 1: Master Key Verification Insert the learned master key and turn the ignition on. Step 2: Key learning Remove the key, insert the key to be learned into the ignition lock(Just insert the key in the off position and do not turn on it to the position!). Wait for about 75s... Key learning succeeded. Now we will show you how to program the remote.
Step 1. Keep the door open, insert the original key into the ignition, and remove it, do this twice. Step 2. Close the door and open it, then close the door again and open it. Step 3. Insert the original key into the ignition and take it out, close the door and open, close the door, and open again. Step 4. Insert the original key into the ignition, close the door, and turn the ignition on and off. Next, we press the lock and unlock buttons on the original key at the same time, and press the lock button. Then we do the same thing on the new key. At this point all the programming is finished, now we can check that the remote control works and that everything is ok. Thanks for watching and for more specific operation details, please refer to M K Locksmith’s YouTube channel. www.obd2shop.co.uk This is a 2007 BMW 550i with all keys lost. Having finished key cutting with Xhorse Dolphin II machine by door code, let's go ahead to program it with Autel MaxiIM IM608 Pro II. IMMO >> BMW >> Smart selection Automatic scan of the immobilizer, the DME, and the EGS will begin. OK >> Key learning Here we can also get the key mechanical code: HA00026203 Dealer key generation will begin. Note: 1. For this CAS type, add a key and all keys lost are applicable. 2. The key learning process requires a network connection for data acquisition. Check the network settings to ensure to connection to Wi-Fi and maintain the network connection during the process. Remove the key from the ignition switch. If it is a smart key, take it out of the vehicle. Be sure to operate as required, otherwise the vehicle may malfunction. If the vehicle fails, try to perform "Clear codes" or contact technical support. Key information read successfully. Do you want to back up the original key data? Yes Save the key data file. Select a blank key position: Key7
Ignition switch generation key >> Semi-smart key The key needs to be preprocessed, otherwise dealer key generation may fail. Do you want to preprocess the key? Yes Connect the Autel IM608 II device to the XP400 Pro Programmer and place the new key into the key slot. Preprocessing key, please wait... Key preprocessed successfully. Insert the key to be learned into the ignition switch. Writing key, please wait... If it is a semi-smart or smart key, perform the steps below: 1. Remove the key from the ignition switch. 2. Insert the key into the ignition switch again. 3. Press the Start/Stop button without starting the vehicle. 4. Press OK to proceed to the next step. Key written successfully. If the vehicle cannot be started or locked steering is indicated on the instrument cluster, synchronizing the ELV or the DME(depending on the reality). Test the new key, it can work perfectly. Done. Customer Issue: When trying to purchase an upgrade on my IM508, I was prompted to upgrade the Personal Center first. However, the upgrade process failed and resulted in the following interface. How can I resolve this? Solutions: Solution 1: 1. Long press the Hex Editor. 2. Click Hex Editor, Force stop, clear default, clear cache, clear data, and then act again. Solution 2: 1. Long press the Hex Editor. Disable 2. Perform the function again 3. Setting>app>disable APK>enable the Hex Editor We hope this is helpful. If you encounter any further issues or require additional assistance, please don't hesitate to reach out to our customer support team for further assistance.
www.obd2shop.co.uk |
Archives
April 2024
Categories
All
|