Customer Problem: My Launch CRP123X cannot recognize the VIN information and the screen displays as below: Solution: Find the settings, clear the cache, then try the update again. After the update, do a firmware repair in the data.
Note: To detect more and accurate VINs, a stable network connection is highly recommended. For technical support of Launch X431 CRP123X Code Reader, please follow https://www.obd2shop.co.uk/wholesale/launch-x431-crp123x-diagnostic-tool.html
0 Comments
Customer problem: I recently got data loss with cas3+ due to poor bluetooth transfer between android device and mini acdp, maybe this time I am lucky because this cas3+ is easy to fix and I wonder what I can do if I had a problem with cas4+ or female module... Solution: Situation 1. If CAS4/CAS4+ is interrupted in the middle and the coding is lost, the coding data can be restored and the vehicle can return to normal. Steps: Select "BMW">>"CAS1-4">>"CAS4/CAS4+">>"OBD Mode">>"IMMO Mileage">>"Recover Coding data". Note: Please connect ACDP to vehicle OBD port before recovering data. Situation 2. If there is an interruption while running FEM or BDC, please do not quit midway, wait for about 15 minutes and the wallpaper will run automatically. If the code is lost, the EEPROM data and coding data on the mobile phone can be reset, and the vehicle can return to normal. Steps: Select "BMW">>"FEM/BDC">>"IMMO Mileage">>"Mode 1: Add key">>"FEM/BDC initial programming process">>"Method 2: Manual single step operation". Then choose "Step 6: Recover EEPROM Data" or "Step 7: Recover Coding Data" for data recovery. For more technical services of Yanhua acdp, please pay attention to http://blog.obd2shop.co.uk/
Customer question: Hi, I use Yanhua Mini ACDP + Module 3 can't read ISN from MEVD172P(N20) F-series controller with (p can) in OBD/CAN mode. What can I do? Solution: You need to use BENCH mode to read the ISN for your car. The following is the operation guide: 1. Select "BMW" >> "DME ISN" >> "BENCH Mode Read/Write DME ISN" >> "BOSCH DME" >> "Fxx" , then select "Help" in N20 (MEVD172P) to connect the device. 2. Please prepare ACDP, OBP+ICP adapter, interface board, and DME. 3. Connect the interface board correctly to the DME interface as shown. 4. Short the CAN resistor on the OBP + ICP adapter to the "CAN-R Join". 5. Connect ACDP, OBP+ICP adapter, interface board and DME. 6. After the connection is completed, go back to the previous interface, select N20 (MEVD172P), and follow the prompts to read and write.
For more technical support on Yanhua Mini ACDP, please follow http://blog.obd2shop.co.uk/ OBDSTAR X300M Tool is able to do mileage adjustments for the 2011 Volkswagen Polo by OBD successfully. The dash odometer now is 67225km. Next, I'm going to show you guys how easy to correct it. Plug X300 main cable into OBD2 port, Vehicles >> Cluster Calibrate >> VW >> VW V31.74 >> Select from vehicle >> Polo >> 2010(NEC+24C32) >> Read write mileage >> Mileage Adjustment Please turn the ignition on, and press ENT to continue. Reading data... Please enter a filename to save. The current mileage of 67200km? Press ENTER to continue. Please input the mileage of the adjustment: 68941km Confirm the value. Please turn the ignition on. Press ENT to continue. Writing data... Adjustment complete. As you can see, the dash odometer has already changed.
OBDSTAR X300M Mileage Adjustment on the 2011 VW Polo was done! You may follow the procedure to correct mileage for other models. Here we've collected Launch X-431 TSGUN TPMS Tire Pressure Detector the most frequently asked questions and answers. Q: Why does my X-431 TSGUN always stay on the welcome screen?
A: if the device keeps displaying the welcome screen, it indicates that it is not in TPMS function mode. If the diagnostic tool is performing the TPMS function, the device will switch to the corresponding function mode. Q: Why is my X-431 TSGUN always displayed in English even the system language of my diagnostic tool is set as non-English? A: The system language of the device varies with the system language of the diagnostic tool that binds it. Currently only English and simplified Chinese are available on the device. If the device detects the system language of the diagnostic tool is non-Chinese, it will change into English automatically no matter which language the diagnostic tool is set as. Q: My X-431 TSGUN does not respond to the diagnostic tool. A: In this case, please carefully check the following: 1. Whether the device is successfully bound to the diagnostic tool. 2. Whether the desired device is ticked in the Bound list. 3. Whether the device is powered on. 4. Whether the device is damaged of defective. Q: Why does my X-431 TSGUN automatically power off? A: Please check the following: 1. Whether the device is fully discharged. 2. If the device is not being charged and there is no operation on the device for 30 minutes, it will automatically power off to conserve battery power. Q: My X-431 TSGUN can not trigger one or more of the sensors. A: Please check the following: 1. Whether the device is damaged or defective. 2. Whether the sensor, module, or ECU itself may be damaged of defective. 3. The vehicle does not have a sensor even though a metal valve stem is present. Be aware of Schrader rubber-style snap-in stems used on TPMS systems. 4. Your device may require a firmware upgrade. Q: What to do if my X-431 TSGUN encountered some unexpected bugs? A: In this case, a firmware upgrade is required. On the TPMS version selection screen, tap "Firmware Update" to upgrade it. www.obd2shop.co.uk Today I'm gonna show how to use Xhorse VVDI Key Tool MAX + Autel MaxiIM IM508 to program 2012-2016 Mazda BT50 ID83 all keys lost. Let's take a look at how easy the job was. Generate Remote via VVDI Key Tool Max Generate transponder >> ID70 ~ ID83(80bits) >> 83-Ford(80 bits) >> 83-Ford(80 bits) >> Generate Complete. Learn Key via Autel IM508 IMMO >> Mazda >> Automatic selection >> Read >> OK >> Yes >> Immo status scan >> Quick erase DTC >> All keys lost(guided) >> Start Note: 1. All keys will be erased. 2. At least 2 keys are required for key learning to complete. Press "Yes". Turn the ignition on. Learned keys: 2 The current number of keys is 0. Erasing successful. Note: All keys have been erased.
At least 2 keys are required for key learning to complete. The following steps need to be completed for the engine to start: 1. Turn the ignition off. 2. Turn the ignition on with the first key, 3s later turn it off and remove the key. 3. Turn the ignition on with the next key, 3s later turn it off and remove the key. Done. Problem: The Launch X431 Creader CRP123X failed to identify VIN. It keeps reading for a while but always fails in the end. What's the problem, please advise. Solution
1. Settings >> Clear cache; 2. Go to re-upgrade; 3. Repair firmware in Data after a successful upgrade. Hope this can help. Technical Support www.obd2shop.co.uk Autel MaxiIM IM508 Key Programming Tool can add 2016 Hyundai Santafe ID46 smart keys by OBD successfully. With free pin code reading, it can be used for programming all keys lost as well. Let's see how easy it is. 1. Read the Password Plug IM508 cable into OBD, IMMO >> Hyundai >> System selection >> Read pin code >> Read pin code(46 smart card) >> Read pincode by OBD The function is only supported for vehicles with a 46-chip smart card, please confirm whether the type of the key is correct! Press "OK". Turn the Hazard warning light on. Open and then close the driver's door once! Reading the password, please wait until 100%... Turn the ignition off(note: the instrument screen is black). The password that is read: 004938 2. Learn Keys Smart key system >> Without slot >> Smart type 8(CAN) >> Remote control learning Press the START button. Press "Smart key learning". This function supports adding keys and all keys lost; Performing this function will erase all existing keys, all the old keys must be relearned again to be able to use normally. Press "Yes" to continue. Turn the ignition off. (note: the instrument screen is black). Open and then close the driver's door once! Please enter the 6-digit security code: 004938 OK >> Yes Note! Click "OK" to complete the following steps:
Within 5s after OK is pressed, use the back or top of the smart key to hold down the START button for 5s until the anti-theft lamps flash. (if the operation failed with the prompts, please remove the key case and re-execute the above steps so that the key chip can be successfully programmed.) Programming succeeded. Press "Yes" to program the next one, and "No" to complete. Number of current keys: 2 Exit the Autel IM508 system and check if the key is programmed successfully. Test two keys. Both can work well, perfectly done!
Here we introduce Vident iSmart800 Pro automotive diagnostic analysis scanner highlights and special functions. Guide to use one-click translation, OBD charging, diagnose cars and reset settings for beginners.
One-click Translation iSmart800 Pro supports 18 languages available & online one-click translation. How to use One-click Translation? 1. Change the iSmart800 Pro tablet language to French in Settings. 2. Click on model diagnosis, here we can see that Auto Scan is still in English, not shown in Fresh. Click the second button above to translate with one-click. After translation, we can find that it has become French.
OBD Charging
When using the OBD cable to connect car and iSmart800 Pro for testing, it can charge the tablet directly. It can also be used when the tablet is out of power.
Diagnose Cars with CAN FD Protocol
Click on Diagnostics, select OBD for Auto Scan. After entering, we can see the diagnostic menu: system status, read codes, erase codes, live data, freeze frame, I/M readiness, O2 monitor test.
How to check real-time data waveform display?
Connect iSmart800 Pro with OBD cable for car. Enter the Diagnostic >> Live Data >> Engine RPM >> Graph When stepping on the accelerator, we can see the engine RPM waveform and its data changes.
Highlights and special features on Youtube:
How to reset iSmart800 Pro settings?
Setting >> Reset Setting Press Reset button to reset all the settings. iSmart will reset after resetting. Press "OK".
Reset setting display on Youtube:
Problem: Super MB Pro M6 + V2022.12 WIN10 SSD has met network problem, it gave the error as below: "Initialisierung des Diagnose-Multiplexers ist fehlgeschlagen. Mogliche Ursachen: Die Verbindung zwischen dem Diagnose-Multiplexer und der Diagnosedose ist unterbrochen. Die Verbindung zwischen dem Diagnose-Multiplexer und dem Diagnosegerat ist unterbrochen. Die Spannungsversorgung an der Diagnosedose (Klemme 30 und (oder)Klemme 31) ist fehlerhaft. Hinweis: Bei Verwendung des SDconnect den Verbindungsstatus uber das Toolkit prufen". (Initialization of the diagnostic multiplexer is failed. Possible causes: The connection between the diagnostic multiplexer and the diagnostic socket is interrupted. The connection between the diagnostic multiplexer and the diagnostic device is interrupted. The power supply at the diagnostic socket(terminal 30 and (or) terminal 31) is faulty. Notice: The connection status when using the SDconnect check via the toolkit.) "Due to network problem, no connection to the SDconnect can be established(749)". "No VCI found.(701) No SDconnect is selected or the desired SDconnect cannot be selected". Solution MB Star Diagnostic Tool needs to revise IP when connecting via network. Please follow the steps below to fix the problem. Selected "Use the following IP address(S)" IP Address(I): 172.29.127.113 Subnet mask(U): 255.255.255.0 Technical Support
www.obd2shop.co.uk |
Archives
April 2024
Categories
All
|